Made in USA - Always has been. Always will be. Made In The USA
AC-DC & DC-DC POWER SUPPLIES
|
Built AND SHIPPED WITHIN 3 DAYS
Buy Direct From Acopian

We’re searching through more than one million products to find the one you need.

Acopian Power Supply Model L36MC140

Infinity Series

Acopian Power Supply Model L36MC140
Power Supply Model:
  • L36MC140 $410.00
      • Nominal Output Voltage:36
      • Output Current Amps:1.4
      • Case Size:LM6A
    • QTY:

Product Overview / Main Screen

Overvoltage Protection Options*$15.00+$35*
 
  OVP set 15% above maximum rated output. Non-latching. (Not available with: Wide Adjust Output models , C9, E5)
  OVP set 15% above maximum rated output. Latching. Includes latching overcurrent option "C9". Reset by momentarily removing AC input power. (Not available with: C9, E5)
  OVP adjustable from Vout minimum to 15% higher than the maximum rated output voltage. Non-latching. Screwdriver adjustment accessible through the top panel. (Not available with: Wide Adjust Output models , E5)
  OVP tracks as Vout is adjusted; OVP triggers between 1v minimum above Vout to 15% above Vout. Latching. (Not available with: Single Output models, E5)
    
IEC AC Input Connector Options$15.00 
 
  IEC inlet on the rear, with accessible fuse. (Not available with: B4, B6, K5, L2, case size LM6A)
  IEC inlet on the front, with accessible fuse. (Not available with: B5, B6, C8, E6, K5, L2)
    
6' IEC AC input Cord 115 VAC$15.00 
 
  (Not available with: E5)
    
6' IEC AC input Cord 230 VAC$15.00 
 
  (Not available with: E5)
    
AC Input Voltage Options 
 
  210-250 VAC input. Internally fused for a single phase source.$15.00
  105-125 VAC or 210-250 VAC input, selectable with switch on rear. Internally fused for a single phase source. (Not available with: B1, B5, B9, K5, case size LM6A)$25.00
  105-125 VAC or 210-250 VAC input, selectable with switch on front. Internally fused for a single phase source. (Not available with: B2, B4, B8, C8, E6)$25.00
  105-125 VAC or 210-250 VAC strappable input. External fusing required. Input voltage of 115 or 230 VAC can be selected by the use of jumpers on a 4 place pluggable terminal block located on the front panel. (Not available with: B1, B2, B3, B8, C8, E6, K5)$20.00
  90-110 VAC input. Internally fused for a single phase source. (Add 5 days to standard shipping time.) (Not available with: C8, E5)$40.00
  22-26 VAC input. Internally fused for a single phase source. (Add 5 days to standard shipping time.) (Not available with: B1, B2, B8, B9, C8, E6, K7, E5)$40.00
  195-220 VAC input. Internally fused for a single phase source. (Add 5 days to standard shipping time.) (Not available with: C8, E6, E5)$40.00
  
Power Switch Options$10.00 
 
  AC on/off rocker switch on front panel. (Not available with: B5, B6, C8, E6, L2)
  AC on/off rocker switch on rear panel. (Not available with: B4, E6, L2, case size LM6A)
    
Voltage Output Adjust and Current Limit Adjust 

(standard:screwdriver slot accessible through the front panel for Vout adjust.)

 
  Front panel knobs; (one for voltage, one for current) used to adjust output voltage and current (Current adjustment range is same as for option C2) (Not available with: Single Output models, E5)$55.00
  Current Limit adjustment screwdriver slot accessible through the front panel. Single Output models: current adjustment range is ±10% of maximum rated output current. Wide Adjust models: current adjustment range is from zero to maximum rated output current. (Not available with: E5)$10.00
  
Inhibit or Enable*$10.00+$35*
 
  Inhibit control, TTL compatible. To disable the supply, apply a voltage between the "Rtn" terminal and the "Inh/Ena" terminal. The voltage can be any value from +3 Vdc to +15 Vdc. (Not available with: E5)
  Enable Control, TTL compatible. To enable the DC output, the "Inh/Ena" terminal must either be shorted to the "Rtn" terminal or pulled to within 0.8 Vdc of the "Rtn" terminal. An open collector or contact closure can be used. (Not available with: E5)
    
Output Programming Options (Wide Adjust models only)*$15.00+$35*

(voltage and/or current)
Voltage mode accuracy: 0.5%. Current mode accuracy is 0.5% or +/- 15mA, whichever is greater. Accuracy percentages do not apply below 5% of output rating.

 
  The output voltage and current may be programmed from 0 to full rating by means of control voltage inputs of 0 to +5 Vdc. (Not available with: Single Output models, E5)
  The output voltage and current may be programmed from 0 to full rating by means of control voltage inputs of 0 to +10 Vdc. (Not available with: Single Output models, E5)
    
Voltage and Current Monitoring, Option “C7”*$15.00+$35*
For models with no programming or with 0-10v programming (option “C6”)
 Voltage Monitor Terminal: Permits remote monitoring of output voltage, stepped down by a ratio of 10:1 (for 3.3v to 90v models) or 100:1 (for 100v to 150v models). Accuracy is 0.5% of maximum rated output voltage.
Current Monitor Terminal:For models with greater than 10 amps output current: permits remote monitoring of output current, stepped down by a ratio of 100 mV/Amp (accuracy is 1% of maximum rated output current). For models with less than 10 amps output current: permits remote monitoring of output current, stepped down by a ratio of 1000 mV/Amp (Accuracy is 1% of maximum rated output current or +/- 15mV, whichever is greater).
For models with 0-5v programming (option “C5”)
 Voltage Monitor Terminal: Permits remote monitoring of output voltage, stepped down by a ratio of 10:1 (for 3.3v to 45v models) or 100:1 (for 48v to 150v models). Accuracy is 0.5% of maximum rated output voltage.
Current Monitor Terminal:For models with greater than 45 amps output current: permits remote monitoring of output current, stepped down by a ratio of 10 mV/Amp. For models with from 5 amps to 45 amps output current: permits remote monitoring of output current, stepped down by a ratio of 100 mV/Amp. For models with less than 4.5 amps output current: permits remote monitoring of output current, stepped down by a ratio of 1000 mV/Amp. (Accuracy is 1% of maximum rated output current or +/- 15mV, whichever is greater).
(When monitoring the output voltage and/or current by means of the monitor terminals, the use of an instrument having an input impedance of at least 10 megohms is recommended.)
 
    (Not available with: E5)
    
AC On/Off Control$35.00 
 
  Apply control voltage between terminals 21 and 22 to turn power supply on. Control voltage range is 11 to 28 Vdc (@ 65ma maximum). (Not available with: B2, B5, B6, B8, E6, K7, L1, L2, L3, E5)
    
Latching Overcurrent Control$5.00 
 
  If current is greater than 15% of the maximum rated output current, the power supply latches off. Reset by momentarily removing AC input power. This option is included with Option A2. (Not available with: Wide Adjust Output models , A1, A2, E5)
    
Over Temperature Protection$15.00 
 
  An internal thermostat will automatically shut down the power supply in the event of an over temperature condition. Power supply resets automatically.
    
Thermostatically Controlled Fan$25.00 
 
  Fan remains off until forced-air cooling is required.
    
Output Blocking Protection Diode$25.00 
 
  Used for battery charging or redundant applications. Derate output by 10%. (Not available with: E5)
    
Transient Protection for Electrically Noisy Environments$35.00 
 
  Transient protection for AC input and DC output. (Not available with: E5)
    
High Frequency Pulsed Load Filtering$30.00 
 
  Recommended for applications such as "switched loads" and "stepper motors". (Not available with: E5)
    
Series Operation Diode$15.00 
 
  Allows power supplies to operate in series, for applications requiring higher output voltage. (Not available with: E5)
    
High Isolation Output$25.00 
 
  May be floated at 1000 Vdc above case. (Available with: Single Output models, B1, B2, B3, B4, B5, B6, B7, B8, B9, D1, D2, F1, K6)
    
AC Inrush Current Limiting$35.00 
 
  AC inrush is limited by a 10 ohm impedance. (Not available with: B2, B5, B6, B8, C8, L2, E5)
    
Table Top Rubber Mounting Feet$15.00 
 
    (Not available with: E5)
    
Alarm with Relay Contacts Options*$15.00+$35*
 
  NC Relay contacts close when output voltage drops more than 10% below nominal. (Not available with: Wide Adjust Output models , E5)
  NO Relay contacts open when output voltage drops more than 10% below nominal. (Not available with: Wide Adjust Output models , E5)
    
Status LEDs on Front Cover*$15.00+$35*
 
  Green LED indicates Vout is between -10% and +15% of rated output. Red LED indicates a fault condition; thermal (for units with option D1), overcurrent, under or overvoltage. (Not available with: Wide Adjust Output models , E5)
    
'Voltage output OK' Monitor*$10.00+$35*
 
  TTL High when Vout is between -10% and +15% of rated output. (Not available with: Wide Adjust Output models , E5)
    
Temperature Monitor*$25.00+$35*
 
  The temperature monitor is used to measure the power supply's internal temperature. Monitor output voltage is set to 2.5 Vdc at 25°C and varies above or below this value by 0.1 Vdc per °C. For example, if the temperature is 20°C the output will be 2 Vdc. (Not available with: H1, H2, H3, H4, H5, H6, H7, H8, E5)
    
Additional, Low Current, Auxiliary Voltage Options*$25.00+$35*

<1% initial Accuracy, ±0.5% Line and ±0.5% Load Regulation, <10mv peak-to-peak ripple. (Not available with option G5.)

 
  Auxiliary output: 3.3 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: 5 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: 12 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: 13.8 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: 15 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: -5 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: -12 Vdc, 0.1 amp (Not available with: G5, E5)
  Auxiliary output: -15 Vdc, 0.1 amp (Not available with: G5, E5)
    
Redundancy ('OR-ing' or 'Blocking Diode')$190.00 
 
  Redundancy is attained by simply wiring two units in parallel. Derate output by 10%.
Includes:
  • Non-latching OVP set 15% above rated output. (Option A1).
  • Alarm with relay contacts that close when output voltage drops more than 10% below nominal (Option G1).
  • Output blocking protection diode (Option E1).
  • Remote sensing.
(Not available with: Wide Adjust Output models , A1, A2, A3, G1, G2, E1, E5)
    
Rear Panel AC Input Fuse$10.00 
 
  (Not available with: B1, B2, B4, B6, case size LM6A, E5)
    
Final Test Data$35.00 
 
  Final test data also includes an extended 8 hour burn-in. (Add 2 days to standard shipping time.)
    
AC on/off LED on Front Cover$10.00 
 
  Red LED indicates AC is on. (Not available with: C8, L2, E5)
    
*The “$35(one-time only charge)” is only added to the total cost of the power supply one time no matter how many options are ordered.
Mounting Kit for Wall Mounting $15.00
GB8 (View drawing of Mounting Kit for Wall Mounting) To mount from the power supply side of the mounting surface, necessary when the other side of the mounting surface is inaccessible. This kit consist of four aluminum brackets and four machine screws for fastening them to the power supply, effectively adding mounting flanges to the power supply.    
Mounting Kit for Wall Mounting $20.00
GBR (View drawing of Mounting Kit for Wall Mounting) To mount from the power supply side of the mounting surface, necessary when the other side of the mounting surface is inaccessible, use accessory Mounting Kit GBR. Required only when end mounting with limited space above and below the supply, this kit consists of four aluminum brackets and uses the existing rear cover screws for fastening them to the power supply.    
Mounting Kit for DIN Rail Mounting (Horizontal mounting) $20.00
LH35DIN (View drawing of Mounting Kit for DIN Rail Mounting (Horizontal mounting)) Horizontal mounting    
Mounting Kit for DIN Rail Mounting (Rear mounting) $20.00
LR35DIN (View drawing of Mounting Kit for DIN Rail Mounting (Rear mounting)) Rear mounting    
Mounting Kit for DIN Rail Mounting (Vertical mounting) $20.00
LV35DIN (View drawing of Mounting Kit for DIN Rail Mounting (Vertical mounting)) Vertical mounting    
Model Number with Selected Options Subtotal
(Not including accessories)

L36MC140

$410
Power Supply Model: L36MC140 $410.00
BACK
If you have a question or problem, or would like to order by phone, please call 1-800-523-9478 (8am-5pm EST M-F)